noll
Full Member
Member since: August 2012
Posts: 522
Aug 28, 2012 9:40:11 GMT -5
Aug 28, 2012 9:40:11 GMT -5
|
Post by noll on Aug 28, 2012 15:27:47 GMT -5
|
|
panzerjager
Full Member
Member since: June 2012
Posts: 204
Jun 5, 2012 21:56:23 GMT -5
Jun 5, 2012 21:56:23 GMT -5
|
Post by panzerjager on Aug 28, 2012 15:42:49 GMT -5
|
|
noll
Full Member
Member since: August 2012
Posts: 522
Aug 28, 2012 9:40:11 GMT -5
Aug 28, 2012 9:40:11 GMT -5
|
Post by noll on Aug 28, 2012 15:51:10 GMT -5
Thanks! This was very helpful! (I used Google translate for the 2nd article ). EDIT: Thanks also chris! I will probably use the putty method as it seems simpler (and harder to spread the smell of burning plastic throughout the house )
|
|
|
Post by TRM on Aug 28, 2012 16:11:16 GMT -5
Looks like you have this one covered Oliver...Great! btw, the smell is not bad and should be really minimal as you shouldn't actually catch the plastic on fire but rather soften enough to stretch. Chris's method is tried and true and is outlined in one of the two articles. Good luck and looking forward to seeing the results.
Dario....thanks buddy for posting the links on this! Two great SBS's on the subject. I added these to the Library here on MSC under Tips and Trick for future reference!!
Thanks again guys!!
|
|
|
Post by 406 Silverado on Aug 29, 2012 7:42:21 GMT -5
Well Oliver, like I said you will get some friendly advice from the fellas here. All are more than willing to help out.
As far as welds go, the fellas have covered the main, popular techniques. The putty method works great as does the sprue method. Keep in mind also that the type of weld you want to replicate will determine which method to use. You can just use the one, as I am sure many do, but I prefer to use both methods. A good example is a long narrow weld bead. I use the sprue for this because I can create a straight and narrow weld without having to use tape.
As for odor, there should be none, unless the flame your using smells. When stretching sprue you don't actually place the sprue in the flame, just to the heat until the plastic softens. When I was your age I stretched my sprue over a 100 watt light bulb. So you see it's the heat that will soften the plastic. A tip on chosing the right plastic to stretch. Some kit companies use a harder plastic for their kits, use a softer plastic as it's easier to stretch and more important it will soften easier and make nicer welds.
Well, hope all this helped some how
|
|
noll
Full Member
Member since: August 2012
Posts: 522
Aug 28, 2012 9:40:11 GMT -5
Aug 28, 2012 9:40:11 GMT -5
|
Post by noll on Aug 29, 2012 9:07:47 GMT -5
Thanks all for answering! In this case ( 4 sets of straight weld lines) I just used dome extra 1/35 tool handles that were the right length. I have some more to do (around a circular hatch, etc), and I will probably use the sprue method than, as the putty that I have (revell) doesn't want to be made into strings.
Thanks all for your help, and I'll post a pic or two in a few minutes to show you how it went (not too badly for a first attempt I think.
- Oliver
|
|
|
Post by bullardino on Aug 29, 2012 9:13:30 GMT -5
I find that the best putty to do the weld seams is some form of the epoxy bicomponent. I tend to go with green stuff rather than milliput, but it's only a matter of personal taste.
|
|
noll
Full Member
Member since: August 2012
Posts: 522
Aug 28, 2012 9:40:11 GMT -5
Aug 28, 2012 9:40:11 GMT -5
|
Post by noll on Aug 29, 2012 9:28:31 GMT -5
here are a couple of pictures: Not too bad for a first try (I hope...)
|
|
|
Post by TRM on Aug 29, 2012 12:56:39 GMT -5
Those beads look fine to me!
|
|
|
Post by wouter on Aug 29, 2012 13:29:35 GMT -5
yup looks good. though I must say I find it hard to get it right myself. On my first Afrika Tiger I used both methods and none were 100% satisfieng to me. Especially with the putty method I find it very hard to roll the putty in very very thin lines...
Cheers
|
|
multicam
Senior Member
Member since: January 2012
Nate
Posts: 2,039
Jan 10, 2012 14:35:41 GMT -5
Jan 10, 2012 14:35:41 GMT -5
|
Post by multicam on Sept 2, 2012 11:20:15 GMT -5
Looks good, Noll. Great work for a first try. Keep it up!
|
|