P-38J Lightning, 1/48 scale

[Whiterook]

I started this build back in August of 2010...the WWII P-38J Lightning.....

Made by Revell, it's 1/48 in scale and was a fairly straightforward kit. I decided to paint it in green with Normandy Invasion Stripes. This is the reference photo I was inspired by.....

[Whiterook]

The parts are a soft plastic...softest plastic I'd ever seen on a kit to that date. It was numbered horribly, and had parts scattered on semi-solid sprues; some parts numbered on one side the the tree, others on the opposite...what a mess!

So on with the show: In the cockpit, with some minor assembly of the seat and steering column, I pre-painting of interior surfaces (including the side walls of the cockpit) Interior Green. The cockpit floor has Interior Green; the seat and backplate have Olive Drab; and the steering column was yet to be painted, a  a pre-base of glossy black. Also to be added was some light gray and aluminum detail painting, and a touch of weathering. I finished assembly of the cockpit, adding in the aluminum foot rests, sides, back, and had to scratchbuild a new control panel, as I'd somehow lost the one that came with the kit! Also in went the radio assembly on the back.

Next up came the rear gun wall. What annoyed me about this kit were the absolutely HORRIBLE instructions! Placement of most parts is a guess, as best....but common sense was my co-pilot! I then cleaned up the wing halves, and finish painted the interior.

Then, I finished painting the cockpit itself, as well as the rear gunwall, which got a duel color of silver and green; finally inserted the whole assembly into the top wing half. Lastly, and undercarriage gun mount/gun wall were done.

On the wing halves went together:  I gotta tell you folks, the discovery of using Testor's Liquid Glue (bottle water like glue with the brush in the lid) at that point in my modeling adventures had made a hell of difference in my modeling; and I keep it in my arsenal, the old standby ModelMaster's liquid glue in the diamond shape bottle with the long metal pipette on the end, which to this day is my first choice to go to. Between the two, I can do anything I need to do.

Next came the landing gear. I had to use some Squadron Putty on what I took to be two model pin holes....errrrrr, that's what you get for not looking further ahead in the manual! They actually were positioning holes for the landing gear support which go on later, so of course, I had to dig out that putty! And all that AFTER I painted the darned things!!! On the pic of the instruction manual, you notice a Radio Operator....that's for the optional Night Flyer version of this bird, which I did NOT build; and actually, I didn't including the Pilot either, as the molding on it are the worst I've ever seen...worse that the Gorilla in my old Bedford QL Gun Portee!

Landing gear painted silver, with Folk Art Acrylic's "Anniversary Silver". Inside landing gear bays painted Interior Green, with Tamiya Acrylics. These would get some color correction during weathering. Then the dual fuselage nacelles were glued together, first putting the landing gear in place...tricky handling needed.

[deafpanzer]

Scary!! Once I built a helicopter kit for my son from Revell and it was TERRIBLE! Plastic was soft that the wheels broke few times so I had to add metal rods to hold them in their places. I am sure it will come out great... rarely see WIPs on P-38 anywhere.

[Whiterook]

Mar 21, 2013 19:54:49 GMT -5 deafpanzer said:

Scary!! Once I built a helicopter kit for my son from Revell and it was TERRIBLE! Plastic was soft that the wheels broke few times so I had to add metal rods to hold them in their places. I am sure it will come out great... rarely see WIPs on P-38 anywhere.

Absolutely!!! I most likely built Revell kits all the time as a kid, but this was the first time I touched a Revell kit since then and I was horrified! But I can't complain, as the kit was bought at Michael's Craft Store, with a 40% off coupon (I know....you're all sick of hearing that!!!), so the kit cost me $12!!!

[Whiterook]

The guns unit Tamiya Gun Metal over Gloss Black, and finally, Folk Art Acrylics "Anniversary Silver" drybrushed in spots.





Next, the ammo magazine was glued on...the instructions were HORRIBLE in placement and orientation, but some dryfitting helped discover the overall placement, and then it was glued in place, and painted with the silver mentioned above, and Folk Art's "Aluminum". The whole unit was then glued in place. Oh, painted the inside of the gun bay Olive Drab









I'll dirty up the ammo can before the end of the build, BTW...looks way too clean.

[Whiterook]

Then, the tail was worked on......






Getting the twin nacelles right had been a bit of a chore, but the seam lines ended up fairly good, regardless. I seem to remember it needed some Squadron Putty.

I needed to weigh down the nose, as she's definitely a tail sitter. That little 'antennae' I errantly cut off and then re-glued back on? Well, after doing some research online and trying in vein to find a bird with that antennae, I figured out that it was the manufacturer's method of elevating the tail from sitting on the ground! I didn't like it! I chopped t back off!!!

As another aside: I found on the bottom of that rear stabilizer fin, the date of the model kit....1964! Ohhhhh geeeeez! Scraped it off....too depressing!

[thug626]

Now THAT is a beast of a kit. . Way to persevere and whip it into shape. P-38's are not easy kits to begin with and to top it off this one is older that I am. Keep up the good work.

Dave

[Whiterook]

Mar 21, 2013 20:17:46 GMT -5 thug626 said:

Now THAT is a beast of a kit. . Way to persevere and whip it into shape. P-38's are not easy kits to begin with and to top it off this one is older that I am. Keep up the good work.

Dave

Thanks mate....it as indeed a bear. I think you'll enjoy the end result. I really wanted t make this a D-Day bird and I feel great about what I was able to make of it.

[Whiterook]

So next came weights...I placed some 3/8 oz. fishing bullet weights. I used was one fishing bullet weight, pushed against the inner side of the ammo canister under the gun rack, and was too tight a fit, so I ground the bullet down a little with a big 'ol file. Yes, I know it's lead....kept that in mind. The other two went in the cowlings of the engines...that makes 3 weights in her front sections, including the nose. I used gel superglue, and it set up wonderfully. I love this stuff! I use the gel CA on my metal 15mm gaming miniatures! Anyway, this is the end result.





She's no longer an tush sitter!

BTW, as a side note: That area you see above the console on the cockpit compartment....it's uneven looking 'cause it is trying to mimic the canvas covering which P-38's have there. Not very well molded..

Next pics are of the wheel bay doors.....Upside down birdie!

Next came some work on the under carriage. Air scoops went on the booms, and then the real fun began (he said sarcastically): The landing gear bay doors. OMG, these are HORRIBLE! (Note a common word here???) The worst I've ever seen, either back in the day or these days. Just plain miserable to attach.

I also put the the front landing gear on, which was equally horrible. The instructions were very misleading and could have been disaterous. Took me much pondering to figure out placement, and I think I nailed it.

[Whiterook]

Also done was some sanding to the Squadron Putty on the top seams of the booms. Came out rather nice.

I put the props and cowlings together and put them on the bird. Revell had a pretty decent mechanism to hold the props on and allow them to turn, which is basically using a cap/collar on the inside post of the prop, hidden in the cowling. I've seen better, with better turn to the props (my Mitchell props turn on a breath!), but it's effective enough for me.

I was thinking of putting some screening inside the intakes of the cowlings, but I couldn't find any references that showed these existed.

[Whiterook]

Work on painting the cockpit and scratchbuilding seat belts. Yeah, they aren't to spec (the seatbelts), but my philosophy.....artistic licence; I'm looking for the 'suggestion', not the patent! I started with something I'd not used before for this purpose....a twist tie!




The twist tie was coated with a plastic sleeve, and unlike usual twist ties, there was no hint of the wire underneath. I bent it to shape and length, plotting out the two straps....then I painted it with Folk Art acrylics' Desert Sand. I then snipped where needed, and superglued them in place. The use of gel superglue changed my hobby-life, in terms of modeling and miniatures!!!

The paint was beat up a tad by my tweezers in placement, but that was cool, as it started a weathering process! Silver linings, right? I would touch up later. I also took some .30 guage wire and made the buckles, which again, are to suggest...not get totally to spec. This is what the looked like, pre-weathering....










This last shot, if you look at the canvas covering for the intrument panel...the molding was actually not too bad, so I decided to stay with what was there and opt away from the tissue method of making canvas. Again, references were not readily available for what it actually looked like; but I had noticed through the cockpit images available on some photos that the canvas did tend to get sun faded and battered, hence the weathering you will see in a bit.

[Whiterook]

The canvas for the instrument panel was weathered with a drybrush method using some Tamiya Buff, and then the pilot seat, with emphasis on the headrest and wear on the seat. The seat was softened up a tad, but I left the headrest more heavily weathered. The radio was darkened in some areas, and then dirtied up a little.

[Whiterook]

Last up was to put the front canopy on.







I like the way the weathered canvas looks through the 'glass'. The canopy stinks!!!! The front edges are not fitted for the fuselage, and would require a little Squadron Putty, unfortunately. The rest of the cockpit canopy will be next to come. 

Then some masking....






The top canopy will be propped open....Command decision!

[Whiterook]

And onward we push!

Some paint! I finished the masking of the cockpit....ended up being too difficult and annoying to use frisket sheet material, so I continued with the Painter's tape. I wonder how liquid mask would work....hmmmmm? I digress. I finished masking, and and also removed the top canopy cover, and then stuffed in a piece of scrap rubber glove into the cockpit itself. Then I airbrush sprayed the whole bird with it's first basecoat.







Note that the door for the front ammo magazines in the nose is only propped on with blue tack....it'll be hinged up when complete. Also, the top canopy cover is off (as mentioned), and will be hinged open as well. I still have the turbo chargers to put in the top, as well....I'd do that after the topcoats are finished.


Overall, I think I nailed the color? I'll be painting the bottom of the bird sky grey, and feathering into the olive drab. And I will naturally be putting the Invasion Stripes on; and weathering, to include darkening in the panel lines, as well.

[Whiterook]

Went online in search of what true color green P-38's were painted in (when they were painted green), and what did I find? The typical (in a lot of modelling) answer of, there is no definitive answer! Arrrgh! Seems the consensus is, when not painted blueish green, black, or a combination of metal and anti-glare panels....well, it's Drab Green.

So, I guess it brought me back to the age old Tamiya colors can leave a lot to be desired in tone and hue, thang. That green looked great on the bird, but it nagged at me that it may not look just right. Taking a cue from actual color photos (what there are of them) online, and the fact that the top surface would exhibit degrees of fading, I decided to lighten up the color by making a mixture of Tamiya Olive Drab, Buff, and White, and shooting it.











I'm good with it!!!

[Leon]

White rook that is some fine work.I really like the p38.

[Whiterook]

And still, the Olive Drab battle went on!!!!

But first, her belly! I sprayed some Tamiya Sky Grey on the old girls bum, and this was the first feathered two tone airbrush work on an aircraft I'd ever done. I researched various OD painted P-38's and they all had the same pattern pretty much in common, especially with the dip of OD under the front side of the engine cowling. I remember feeling more comfortable with the airbrush every time out, but I still needed a lot of improvement, IMHO. I have to relax more with it, plain and simple. But I also have to say, my model painting was forever changed for the better with the introduction of airbrushing in my bag of tricks!

This is the bird with her belly up in my spraybooth....



The turntable she lays on is a kitchen spice and can carousel, and a plastic cake trivet that has small plastic feet that fit on the rubberized surface of the carousel.

I got the inside of the wheel well bays with Sky Grey, as every resource material reference I've seen mentions this was painted this way; as opposed to what Revell's build manual says (OD). Sky Grey made more sense.

[Whiterook]

Mar 21, 2013 20:52:00 GMT -5 Leon said:

White rook that is some fine work.I really like the p38.

Thanks!!!  I appreciate the encouragement!

[Whiterook]

And now, the moment you've been waiting for....the new and hopefully improved () Olive Drab.....



A better shot of the feathering....





And this is the supercharger, which I painted Tamiya Flat Brown, and will get some silver detailing highlights later....

[Whiterook]

Nick (Geek44) turned me on to a neat method to get cleaner demarcation lines....the use of silly putty or blue tack! What you will see next is actually another brand of blue tack....same stuff, just not blue! 



Anyway, though he thought the freehand demarcation between the OD and Sky Gray looked good, I thought it could use a little tweaking in a couple spots, so I tried the method out...






Then with a re-spray.....

[Whiterook]

I think this makes a world of difference in control of the demarcation line between colors. It was a turning point for me with a more proper technique. Let me show you what I mean: here's a shot from before....

So what do you all think?


And lastly, a coat of Future on most surfaces, which would stand overnight for the surface tension to relax and smooth out. Invasion Stripes and decals to come!

[Leon]

Think you nailed that spot on.

[Whiterook]

Invasion Stripes.

I knew they were going to be the new territory on this build for me, and I needed experience in masking models at that time in my modeling career, as I didn't know much on the subject. I wanted to do more challenging camouflage schemes with my other projects, so this was a good test bed. I thought I'd be clever and go out and buy real airbrushing masking frisket....well, that didn't quite work out! Honestly, I think the stuff is more for 2-D than 3-D projects. It just doesn't have any staying power on plastic.

Tamiya tape....yup, I'm sure the stuff is brilliant. Gonna buy some at my earliest convenience. I saw some once at a local hobby shop and the stuff was maybe less than a quarter inch wide; the fact that the hobby store specializes in model railroading probably had something to do with that . So I opted for the next best, available thing....my trusty old Painter's Tape!

Using an artist's brush, I hand paint the stripes. To get a start, I did a few white stripes by masking first with tape, and then carefully edge brushing and filling in. I was well on the way.

[Whiterook]

Mar 21, 2013 21:06:45 GMT -5 Leon said:

Think you nailed that spot on.

Thanks....that means a lot to me!!!

[Whiterook]

The wings were finished, and the booms just started (hence not looking finished yet). I was using Folk Art Acrylics, by the way.









Not a lot of the stripes were masked....I actually would hand paint more than mask. For instance, all the black is hand painted with no masking. It was just easier that way.

[Whiterook]

The booms' invasion stripes were finished. Then, I propped up her magazine compartment door in the nose, and I decaled the door with some Nose Art....the "K" is hand painted and is an homage for my wife (Karen), and I'll make her a brunette after the decal Micro Set cures! Note that Future is used on the exterior prior to decaling and weathering.



You may note the weathering....chalk wash did the trick for now, I really have very little experience weathering aircraft and will likely do a little more later down the road as I figure it out.







The decals were pretty nice, and I opted to go minimal. I did a lot of research on these birds and noted that a lot of them had minimal evidence of the stuff...not sure why. The Invasion Stripes came out quite well. I painted the tires a hand blended color. I also put silver back on the landing gear.



After I matte coat her coming up, I'd paint the props and place decals on those, remove the tape masks off the cockpit, and she would be ready for finished snap shots.

[Whiterook]

And the finished product....

[bbd468]

Hey bro, Fine war bird WR! The D-day stripes looks awesome too...well done!

[Whiterook]

Mar 21, 2013 21:18:56 GMT -5 bbd468 said:

Hey bro, Fine war bird WR! The D-day stripes looks awesome too...well done!

hey, thanks man....It's one of my favorite pieces.

[bbd468]

Mar 21, 2013 21:22:04 GMT -5 Whiterook said:

Mar 21, 2013 21:18:56 GMT -5 bbd468 said:

thanks man....It's one of my favorite pieces.

And rightly so! Whats the next past build surprise?